Janome 4400 manual

The gap between the needle and the flat surface should be consistent. Never use a bent or blunt needle. Always test thread and needle size on a small piece of fabric which will be used for actual sewing.

The blue tipped needle effectively prevents skipped stitches. Lift up the spool pin and place the spool of thread on it with the thread coming off the spool as shown. Gently slide the hook cover plate release button to the right and remove the cover plate. The thread slips. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Memory Craft Do not use outdoors. Do not use bent needles. Screen Sharpness Adjusting Dial Use this to adjust the sharpness of the liquid crystal display. Extension Table The extension table provides added sewing surface and can be easily removed for free arm sewing.

Detaching the table: Pull the table away from the machine, as illustrated. Attaching the table: Push the extension table until it snaps into the machine. Turn off the power switch, and insert the foot control plug q , machine plug w , into the machine and power supply w plug e into the outlet in the following order.

Do not touch any moving parts such as the e thread take-up lever, handwheel or needle. Controlling Sewing Speed Speed setting lever The maximum sewing speed can be controlled by the speed setting lever. Foot control Sewing speed can be varied by the foot control. Press button again for single needle sewing. You can store a maximum of 50 programmed patterns and sew. SEN [Number keys] Press number keys of the pattern number to select the desired pattern. Language selection setting t z Turn on the power switch while pressing the memory key.

The feed dogs must always be up for normal sewing. Align the setting mark on the lever with the desired number. Turn off the power switch. Loosen the needle clamp screw by turning it counterclockwise. Tighten the clamp screw firmly by turning it clockwise. The presser foot will drop off. Tighten the screw by turning it clockwise. Press the large spool holder firmly against the spool of thread. Lift out the bobbin. To use, insert the spool stand and the additional spool pin in the hole.

Place the felt and spool on the pin with the thread coming off the spool as shown. With the free end of the thread held in y your hand, depress the foot control. Stop the machine when it has made a few turns, and cut the thread close to the hole in the bobbin.

When the bobbin is fully wound, it will stop automatiaclly. The thread slips into notch B. Let us know if you have any questions! We're happy to help. Thank You for Signing Up! Join our mailing list for Coupons and Promotions! Sign Up! Hemostat 5. Applique Embroidery Scissor. Close Start Your Application In a few short steps you could own the machine of your dreams with convenient monthly payments and promotional financing.

Just follow these steps during checkout: Enter your Synchrony Financial account or card information. You can apply online at that point if you don't have one already Fill out our shipping and billing information fields. Agree to Synchrony Financial's terms and conditions. Press this key to enter the setting mode.

You can customize the machine settings to your preference. The machine settings for common settings, embroidery and language selection are available in this mode. Press this key to view the step-by-step visual guide about the essential operations.

Press this key to lockout the machine when threading the machine, replacing the accessories etc. Attach the large spool holder, and press it firmly against the spool of thread. Hold the thread with both hands and wind it around the bobbin clockwise several times. Insert the thread into one of the slits of the flange plate and pull the thread to cut. For safety purposes, the machine will automatically stop 1. The thread will be cut to a proper length and held in place.

Push down the hook cover plate to fit in place. Hold the thread with both hands and pass the thread into the slit of the pre-tension thread guide. Lower the presser foot. Turn the handwheel toward you to until the needle thread sign w appears on the right upper corner of the lockout window.

The threader hook comes out through the needle eye from behind. Always make sure to press the lockout key to lockout the machine or turn the power switch off before replacing the needle. A loose needle or a loose screw may cause machine malfunction or needle to break. Insert a new needle into the needle clamp with the flat side of the needle to the rear. When inserting the needle into the needle clamp, push it up against the stopper pin and tighten the needle clamp screw firmly with a screwdriver.

To check needle straightness, place the flat side of the needle onto something flat a needle plate, glass etc. The gap between the needle and the flat surface should be consistent. Select the help topic by pressing the book icon and the step-by-step instruction will open. Remove the embroidery foot when removing the needle plate for the maintenance, etc. Always make sure to press the lockout key to lockout the machine or turn the power switch off before removing or attaching the embroidery foot.

Raise the needle by turning the handwheel toward you. Replace the standard bobbin holder with the bobbin holder for embroidery high tension when using bobbin threads other than Janome bobbin thread for embroidery. Always make sure to press the lockout key to lockout the machine or turn the power switch off before attaching the bobbin holder.

Make sure to match the knob of the bobbin holder with the stopper on the machine. Use the standard bobbin holder when sewing quilting designs that use the same thread for the bobbin as the needle thread. Attach the stabilizer to the wrong side of the fabric.

You may need to use more than one layer. The non-adhesive type should be used when embroidering fabric which cannot be ironed or for sections which are difficult to iron. Cut the stabilizer larger than the embroidery hoop and set it on the hoop so that the entire piece is fastened to the hoop to prevent any looseness in the fabric.

Place the wrong side of fabric and the glossy side of the stabilizer together. Fold up a corner of the stabilizer and fuse it with an iron. Fold up a corner of the stabilizer, to make it easier to peel off the excess stabilizer after stitching. Ironing temperatures vary depending on the kind of adhesive stabilizer you are using.

Sticky type stabilizers can be used only for securing a small piece of fabric or work that cannot be secured in the hoop, or for securing velvet and other napped fabric that would be permanently marked by the hoop.

Turn the handwheel toward you to raise the needle at its highest position. Press the lockout key to lock the machine. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Memory Craft E. Grouping patterns Connecting the Power Supply z First make sure the power switch q is off. WARNING: While in operation, always keep your eyes on the sewing area, and do not touch any moving parts such as the thread take-up lever, handwheel or needle.

Always turn off the power switch and unplug the machine from the power supply: - when leaving the machine unattended. For the U. Do not modify the plug in any way. Raising and Lowering the Presser Foot You can raise and lower the presser foot with the presser foot lifter. NOTE: Do not turn the hand wheel when the presser foot is in the extra lifted position.

Use the touch panel stylus included in the standard accessories. To reduce the risk of injury, all the buttons and keys are deactivated. To unlock the machine, press the lockout key t again. Setting the Spool of Thread Lift up the spool pin. Place the spool of thread on the spool pin. NOTE: Use the small spool holder to hold narrow or small spools of thread.

Insert the extra spool pin into the hole as shown. Place a spool of thread on the extra spool pin and fix the spool with the spool holder.

PDF manuals are free to download and easy to search. Go to its web page. If your machine is an older model, look for it under "Retired. Click on the "Download Manual" link in the upper right corner of the frame. The manual will open in a new window in your browser.